The [레이아웃] tab allows you to specify the imposition of the pages. Optionally, you can configure additional layout settings. For example, you can add print marks like registration marks, barcodes and colour strips to your document. The options in this tab are available in four levels.
|
Level |
Settings |
|---|---|
|
1 |
|
|
2 |
Open the settings of the [임포지션 템플릿]. The following settings become available:
|
|
3 |
Open the settings of the [인쇄 표시]. The available print marks become available. |
|
4 |
Define the settings for most print marks. |
|
Setting |
Description |
|---|---|
|
You can configure a number of the options. Click the pencil icon to open the settings of an option. |
|
Click the collapse icon to close the settings of an option. |
|
Save your changes. |
Option [표지 용지] is disabled if your document has no cover.
You can select a default media size from the drop-down list, for example 'A4' and 'Letter'.
You can create a custom media size. Select [사용자 정의] from the drop-down list and change the [폭] and [높이]. Define the unit for the custom media.
The [세로] and [가로] settings allow you to specify the sheet orientation.
The following settings are disabled when your document contains both portrait and landscape media: [폭], [높이], [세로] and [가로].
You can select a default media size from the drop-down list, for example 'A4' and 'Letter'. This sheet size is applied to the whole document.
You can create a custom media size. Select [사용자 정의] from the drop-down list and change the [폭] and [높이]. Define the unit for the custom media.
The [세로] and [가로] settings allow you to specify the sheet orientation.
The following settings are disabled when your document contains both portrait and landscape media: [폭], [높이], [세로] and [가로].
Imposition consists of the arrangement of the pages on the sheet, in order to obtain faster printing, simplify binding and reduce paper waste. Correct imposition minimizes printing time by maximizing the number of pages per impression. To achieve this, the printed sheet must be filled as fully as possible.
You can select an existing imposition template. Optionally, you can configure additional layout settings. For example, you can add print marks like registration marks, barcodes and colour strips to your document. The value of option [임포지션 템플릿] becomes [사용자 정의] to indicate that you are no longer using a default imposition template. You can save the combination of imposition template and additional settings to create a custom imposition template.
The default imposition templates offer basic imposition. For example, the template [2-up(단면)] places two pages on one sheet side. No additional layout settings are applied to the document. A subset of the imposition settings is available when different media sizes are used in the document. The different imposition types are grouped and explained below.
[없음]
[사용자 정의]
Use option [임포지션 유형] to create a custom arrangement of the pages on the sheets. The value of option [임포지션 템플릿] becomes [사용자 정의].
[2-up(단면)] / [2-up(양면)]
Two pages are placed on each sheet side in the (left to right) reading order.
[16-up(단면)] / [16-up(양면)] / [4-up(단면)] / [4-up(양면)] / [9-up(단면)] / [9-up(양면)]
4, 9, 16 pages are placed on each sheet side in the (left to right and top to bottom) reading order.
[VDP 4-Up]
4 pages with variable data are placed on one sheet side in the (left to right and top to bottom) reading order.
[Folio]
Four pages per sheet are placed in a way that each sheet can be half folded. All the folded sheets are stacked.
[Octavo]
Generates the same imposition as the [Octavo 접장] document type.
[Quarto]
Generates the same imposition as the [Quarto 접장] document type.
The Cut & Stack imposition enhances printer productivity when printing large documents. For example, two pages are printed per sheet side. The sheets are cut in two parts. The left stack is stacked on top of the right stack to form a perfect sequential order.
[잘라내기 및 스택]
The left and right pages are printed in the same orientation.
[안쪽 가장자리 제본으로 잘라내기 및 스택]
The left pages are rotated 180 degrees compared to the right pages. The binding edges of the pages are on the inside of the sheet.
[바깥쪽 가장자리 제본으로 잘라내기 및 스택]
The right pages are rotated 180 degrees compared to the left pages. The binding edges of the pages are on the outside of the sheet.
[잘라내기 및 스택 - 4 스택]
Four pages per sheet side are placed in a way that, after cutting the paper in 4 parts, the piles are stacked to build the full document.
[VDP 잘라내기 및 스택 - 4 스택]
Four pages with variable data are placed on one sheet side in a way that, after cutting the paper in 4 parts, the piles are stacked to build the full document.
[안쪽 가장자리 제본으로 동일한 이미지 찍기]
The same page is printed twice per sheet side. The left pages are rotated 180 degrees compared to the right pages. The binding edges of the pages are on the inside of the sheet.
[바깥쪽 가장자리 제본으로 동일한 이미지 찍기]
The same page is printed twice per sheet side. The right pages are rotated 180 degrees compared to the left pages. The binding edges of the pages are on the outside of the sheet.
For example, use this option when pre-punched paper is used with the punched holes on both ends of the paper.
[VDP 동일한 이미지 찍기]
The same page with variable data is printed twice per sheet side. The pages are printed with one edge attached to each other. For example, use this option when you want to print a ticket with ticket stub.
You can select which PDF box should printed. The content of the selected PDF box will be printed. Or use a custom print area.
[사용자 정의 도련 영역]
Click the edit icon to the right to enter a distance from the page edges.
That distance will be taken inward from the largest PDF box to determine what the printed page content will be.
Use option [임포지션 템플릿] to select an existing arrangement of the pages on the sheets.
Use option [임포지션 유형] to create a custom arrangement of the pages on the sheets. The selected [문서 유형] determines which values are available in the drop-down list. The value of option [임포지션 템플릿] becomes [사용자 정의] to indicate that you are no longer using a default imposition template.
[가로] and [세로]
Define the number of pages that must be imposed on one sheet side.
[중첩]
Option [중첩] becomes available when you have selected value [잘라내기 및 스택] for option [임포지션 유형].
[스택당 페이지]
Arrange the pages in stacks. The stacks are created in the order of the value of option [시트에 페이지 정렬]. The first page is imposed on the first sheet, the second page on the second sheet until you have reached the last sheet. These pages form the first stack. The second stack starts again on the first sheet and moves down until the last sheet is reached. Et cetera.
For example:
Your document is 1-sided and contains 40 pages. You have selected [잘라내기 및 스택] with two pages horizontal and two pages vertical. So, four pages are printed per sheet. The value of option [시트에 페이지 정렬] is [좌측에서 우측, 상단에서 하단으로]. The application starts arranging the pages in four stacks. The first stack starts with the page in the left-top, The second stack starts with the page in the right-top. Left-bottom the third stack and right-bottom the fourth stack. The first 10 pages are arranged in the first stack, the next 10 pages in the second stack, et cetera. The sheets are cut in four parts. The stacks are stacked on top of each other according to the value of option [시트에 페이지 정렬]. The four stacks form a perfect sequential order of the pages.
[시트당 페이지]
Arrange all pages for the first sheet, then move one sheet down to arrange the pages for the next sheet, etc. Arrange the pages per sheet in the order of the value of option [시트에 페이지 정렬].
[시트에 페이지 정렬]
Option [시트에 페이지 정렬] becomes available when you have selected value [잘라내기 및 스택] for option [임포지션 유형].
The value of option [시트에 페이지 정렬] determines the arrangement of the pages on the sheets.
[회전]
Option [회전] becomes available when you have selected value [잘라내기 및 스택] for option [임포지션 유형].
Rotate pages 180 degrees.
The value determines which pages will be rotated. For example, 3x3 pages are imposed per sheet side in three horizontal rows and three columns. Select [세로 홀수] to rotate all pages in the first and third column.
Use option [동일한 이미지 찍기] to repeat the imposed pages as defined by the [임포지션 유형]. The imposed pages will be repeated per sheet side. The option [동일한 이미지 찍기] becomes available when you select value [잘라내기 및 스택] for option [임포지션 유형].
For example, you have selected [잘라내기 및 스택] with two horizontal and two vertical pages per sheet side. Then, you select [동일한 이미지 찍기] with value two for horizontal and two for vertical. Now, the four imposed pages as defined by [임포지션 유형] will be repeated two times horizontally and two times vertically.
Select how you want to repeat the imposed pages as defined by [임포지션 유형]:
[1]:
No repetition. Use the imposed pages as defined by [임포지션 유형].
[사용자 정의]:
Define the repetition of the imposed pages as defined by [임포지션 유형] yourself with the [가로] and [세로] settings.
Gutters
Define the distance between the pages on the sheet with the horizontal and vertical gutter. You cannot define a negative gutter.
[자동 거터]
[수동 거터]
[유형 임포지션용 거터]
Use option [임포지션 유형] to create a custom arrangement of the pages on the sheets. For example, you have selected [잘라내기 및 스택] with two horizontal and two vertical pages per sheet side. Use option [유형 임포지션용 거터] to define the gutters for the pages imposed on the sheet by option [임포지션 유형].
[동일한 이미지 찍기용 거터]
Use option [임포지션 유형] to create a custom arrangement of the pages on the sheets. For example, you have selected [잘라내기 및 스택] with two horizontal and two vertical pages per sheet side. Use option [동일한 이미지 찍기] to repeat the imposed pages as defined by the [임포지션 유형]. For example, you have selected [동일한 이미지 찍기] with value two for horizontal and two for vertical. Now, the four imposed pages per sheet side defined by [임포지션 유형] will be repeated two times horizontally and two times vertically. Use option [동일한 이미지 찍기용 거터] to define the gutters between each repetition of the four imposed pages.
[도련 사용]
Use the bleed box instead of the trim box of each page. The bleed box may contain a bleed area in addition to the page content. Usually, the bleed area is 3 to 5 mm larger than the trim box.
Alignment
Define the position of the page on the sheet with the shift and the horizontal and vertical settings. You can define a negative shift.
Use option [양면에서 동일] to put the page on the same position on the front side and back side of the sheet.
Disable [양면에서 동일] to handle the position on [앞면] and [뒷면] separately.
You can define which marks are printed on the output media. You can define if the selected marks must be printed on all sheets or only on the first sheet.
[제본 가장자리에 표시 없음]
You can select to not print any marks along the binding edge, for example, when your document is a booklet.
[모서리 재단 표시]
These marks are lines printed in the corners of the sheets to indicate where to trim the paper.
You can define the size, location and the stroke of this print mark.
[중앙 표시]
Centre marks are vertical lines used to indicate the centre of the printed page. For example, the centre of the spine of a booklet.
You can define the size, location and the stroke of this print mark.
[접기 표시]
Fold marks are vertical lines used to indicate where the printed page must be folded. The fold marks overwrite centre marks.
You can define the size, location and the stroke of this print mark.
[작업 무결성 표시]
You can add the sheet number and the sheet side to the printed pages.
You can define the location of this print mark.
[세초 표시]
Use this option to print black marks on the outside fold of each signature in bookbinding.
The black marks are positioned differently on the outside fold of each signature in bookbinding to aid in collating.
[바코드]
You can create an automated workflow for finishers by using a barcode and a registration mark for finisher. For example, the automated workflow can be used for the Duplo DC-646. See topic "Automated workflow by using barcodes for finishers, for example, the Duplo DC-646" in the technical service manual.
The barcode and readable text are always black when you define a barcode in the [생산] workspace.
Four settings ensure the readability of the barcode: checksum for [1D 바코드] or error correction for [2D 바코드], minumum size of the barcode, quiet zone and resolution.
In barcode technology, a quiet zone is the blank margin on either side of a barcode that's used to tell the barcode reader where a barcode's symbology starts and stops. The purpose of a quiet zone is to prevent the reader from picking up information that does not pertain to the barcode that is being scanned. The blank margin will not send a scanning signal, hence the name "quiet".
[1D 바코드]
A 1D barcode should have a quiet zone of at least 6 mm on each horizontal side and at least 1,6 mm on each vertical side.
[2D 바코드]
A 2D barcode should have a quiet zone of at least 2 mm on each side.
You have to configure the quiet zone and the resolution in the configuration file. Browse to the config file and open it using a text editor, for example, Notepad:
C:\ProgramData\Oce\PRISMAcore\Configuration\PRISMAcore.Plugin.PBE.AppSettings.config
"BarcodeResolution" value="600"
The default value for the resolution is 600. Possible values: 300 or 600. An unsupported value is ignored and 600 is used instead.
"BarcodeWhiteBorderSize" value="3"
The horizontal and vertical margins form the non-printable area, or quiet zone, around the barcode. The default value is 3 mm. The horizontal and vertical margins both use the value of "BarcodeWhiteBorderSize".
When the barcode is rotated, the minimum values for the quiet zone are rotated accordingly.
[텍스트]
The typed text and any variables are encoded as a barcode. The barcode type determines whether you can use digits, text, variables or a combination of these in the text. You can add the sheet number, the total number of sheets and the job name to the text of the barcode. Finishers can use this information to check if the order of sheets is correct and to check if the job contains all sheets.
|
Icon |
Description |
|---|---|
|
Click this icon to add the sheet number as a variable to the text for the barcode. The actual sheet number is automatically added for each sheet that contains a barcode. |
|
Click this icon to add the total number of sheets as a variable to the text for the barcode. The actual number of sheets is automatically added for each barcode. |
|
Click this icon to add the job name as a variable to the text for the barcode. The actual job name is automatically added for each barcode. |
[최소 자릿수]
Some finishers require a minimum number of digits for the sheet number and/or total number of sheets. The maximum value is 10. "0" is used as padding character.
[유형]
[1D 바코드]
Linear or 1D barcodes use a series of variable-width lines and spaces to encode data. Linear barcodes hold just a few dozen characters, and generally get physically longer as more data is added.
1D barcodes are dependent on database connectivity to be meaningful. If you scan a UPC code, for instance, the characters in the barcode have to relate to an item in a pricing database to be useful.
[2D 바코드]
2D barcodes use patterns of squares, hexagons, dots, and other shapes to encode data. They can be much smaller while holding more data (hundreds of characters) than 1D codes. Data is encoded based on both the vertical and horizontal arrangement of the pattern, thus it is read in two dimensions.
A 2D barcode doesn't just encode alphanumeric information. These codes can also contain pages, website addresses, voice, and other types of binary data. That means you can make use of the information whether you are connected to a database or not. A large amount of information can travel with an item labeled with a 2D barcode.
[인코딩]
The selected barcode type determines which barcode encodings are available to you.
[체크섬] or [오류 수정]
[1D 바코드]
Checksum information can be stored in the barcode to verify the barcode is correct.
[2D 바코드]
There are four error correction levels used for QR codes. Each level adds different amounts of "backup" data to the QR code. The selected level depends on how much damage the QR code is expected, and hence how much error correction may be required:
Level L - up to 7% damage
Level M - up to 15% damage
Level Q - up to 25% damage
Level H - up to 30% damage
[사용자가 읽을 수 있는 텍스트]
Enable this option to add the text of the barcode directly under the barcode. Or disable this option to only show the barcode.
[최소 크기]
Some finishers require a minimum barcode size. The minimum size encompasses the barcode, the margins and the readable text under the barcode.
[시트의 위치]
You can define the location of the barcodes. Use the options [시트의 위치] and [이동].
[컬러 스트립]
You can add a colour strip to the front side of the printed sheets. The colour strip will not be added to the back side. Colour strips are used in PRISMAprepare as colour proofing strips on the printed output.
[피니셔용 맞춤표]
Select a registration mark and configure the position of the registration mark on the sheet.
You can create an automated workflow for finishers by using a barcode and a registration mark for finisher. For example, the automated workflow can be used for the Duplo DC-646. See topic "Automated workflow by using barcodes for finishers, for example, the Duplo DC-646" in the technical service manual.
[맞춤표]
Registration marks print outside the trim area of the page. They can include bulls-eye targets, corner trim marks, etc. These marks allow the operator to accurately align printed pages and better align cuts when trimming.
[파일 이름]
Print the file name on each page.
[인쇄 날짜]
Print the print date on each page.
[비고]
Print the remarks on each page.
Use [크리프 보상] to make sure that the margins on all pages are equal after the booklet is folded and trimmed. The [크리프 보상] factor is calculated from the [두께] of the media.
For example:
You have 30 sheets which you fold to make a booklet. The sheets in the middle of the booklet stick out compared to the cover of the booklet. When you trim the sheets that stick out, the distance between the page content and the sheet edges is changed. This means that the page content creeps towards the edge of the sheets due to the trim action.
[없음]
[바깥쪽]
Shift the page content to the outside of the booklet.
[안쪽]
Shift the page content to the inside of the booklet.
[계산된 두께] / [계산된 첫 번째 제본 두께]
PRISMAprepare automatically recalculates the thickness of the booklet when the number of sheets or the thickness of the media changes.
In case of a booklet, the computed booklet thickness is the spine size.
In case of a multi-booklet, the computed thickness is:
The thickness of one output group when each output group contain a constant number of sheets. If the last booklet has less sheets, its thickness is calculated but not displayed.
The thickness of the first output group when the output groups contain different numbers of sheets. The thickness of the other output groups is calculated but not displayed.
[제본 두께] / [첫 번째 제본 두께]
You can increase or decrease the creep compensation by changing the booklet thickness. The maximum difference is 5 mm compared to the computed thickness.