Loading

Calibrate a media family

The goal of the media family calibration is to achieve consistent colour quality over time for media of the same media family.

Calibrate a media family in the following situations:

  • After the installation of the print system, for the default coated and uncoated media families.

  • When you create a new media family.

  • When your Service organisation replaces system parts.

  • When you want to keep the print quality high for frequently used media families.

A curve icon indicates that a media family is not calibrated. This icon appears when a new media family was created without calibration or when the timer for media family calibration expires.

Media family calibration options

Tools

i1 spectrophotometer.

Before you begin

For more information about:

Procedure

  1. Calibrate the printer. (Calibrate the printer)
    IMPORTANT

    You must always perform a printer calibration before you continue with this procedure.

  2. Connect the i1 spectrophotometer to the USB port of the control panel.
  3. Touch [System]  → [Colour adjustment]  → [Calibrate media family].
  4. Select the media family to calibrate.
  5. Select the media for calibration, if required.

    The system displays the default selected media for calibration.

  6. Select [Use halftone normal as basis] to shorten the media family calibration.
  7. Load the calibration media.
  8. Touch [OK].
  9. Follow the instructions on the control panel.

Results

After media family calibration, the feedback window shows the results of the performed procedure.

Feedback window of media family calibration procedure

When you see two green checkmark icons, touch [OK] to save the new calibration curves.

When you see a red cross icon, use the table below to evaluate the result. Then, click [OK] to save the new calibration curves or [Cancel] to discard the results.

Feedback screen

Remarks

Description

The CMYK lines in the graph show how many percent the colour differs compared to the previous media family calibration.

The [Highest difference] and [Average difference] values of the [Comparison with previous calibration] information are indicators for the frequency of the media family calibration.

NOTE

For the first media family calibration there are no reference values and thus no feedback information.

Evaluation

  • When the [Highest difference] value colour is less than about 2 for each colour, you can calibrate less often without noticeable loss of colour quality.

  • When the [Highest difference] value is between about 2 and about 4 for each colour, you are advised to continue calibrating with the current calibration frequency.

  • When the [Highest difference] value is greater than about 4 for one or more colours, you are advised to calibrate more often to achieve a more stable colour stability.

Description

The ΔE values of the [Paper white and primary colours differences] information are indicators for the difference between the reference values and measured values.

The [Reference Lab values] are taken during the first media family calibration.

Evaluation

  • When each ΔE value is less than the tolerance level, the colour quality is fine.

  • When a ΔE value is greater than the tolerance level, first check that the media used is the same as the media used in the first media family calibration. Then, if required, check the printer condition.

Description

The ΔE values of the [Measurement accuracy] information are indicators for the accuracy by which the patches are printed and measured.

The control panel displays a heatmap whose patch locations correspond with the printed chart.

Evaluation

  • When the average ΔE value is less than the [Value where heatmap turns green] value the patches on the control panel turn green and the colour quality is fine.

  • When the average ΔE value is between the [Value where heatmap turns green] value and the [Value where heatmap turns red] value, the patches on the control panel turn orange-like and the colour quality can still be fine. However, you might want to try the options in the list below.

  • When the average ΔE value is greater than the [Value where heatmap turns red] value the patches on the control panel turn red. You are advised to try one or more options in the list below.

Options to improve colour quality

  • Check the patch on the printed chart

    On the control panel, use the > and < symbols to scroll through the calibration charts. Use the zoom symbol to zoom in or out.

    Then, touch the red patch to find the row and column number to check the corresponding patch on the printed chart to solve the problem. Then, calibrate the media family again.

  • Calibrate the media family again

    Something may have gone wrong during the use of the i1 spectrophotometer.

  • Calibrate the printer

    See Calibrate the printer.